Type 0820 is een tweedelige dubbelwerkende zuigerafdichting die bestaat uit een speciaal gemengde PTFE-profielring en een o-ring als bekrachtigend element.
Toepassing
Spuitgietmachines, heftrucks, hefplatforms, kranen, landbouwmachines, hulpstukken in hydraulische en pneumatische systemen.
Technische informatie
Lage wrijving, geen stick-slip
Geringe axiale hoogte
Lange levensduur
Hoge glijsnelheid
Groot temperatuurbereik en grootste mediaweerstand afhankelijk van materiaalkeuze O-ring
Kleinste wrijvingscoëfficiënt en dus geen energieverlies
Groot bereik
Werking
Wij adviseren een speciaal montagegereedschap en een vrij toegankelijke inbouwruimte voor een diameter van <40 mm. Het montagegereedschap moet vrij zijn van scherpe randen en bramen. Voor de montage worden de afzonderlijke onderdelen ingevet of geolied met afdichtingscompatibel vet op basis van minerale olie of met het medium van het systeem.
Opties
Bij gebruik in cilinders met lange slag of bij zijdelingse krachten worden ten minste twee geschikte zuigergeleidingsringen / banden aanbevolen, voor korte slagen of minimale doorbuiging ten minste één zuigergeleidingsring / -band. Zuigerafdichtingen type 0820 kunnen op aanvraag worden vervaardigd uit temperatuur- en mediumbestendige FKM / PTFE-compounds. De waarden voor de toegestane afdichtingsgroef van de 0820 zuigerafdichting vindt u in onderstaande tabel.
Tabellen
OPERATING CONDITIONS
MEDIA
Mineral oils (DIN 51524)
HFA and HFB
HFC
TEMPERATURE
from -30°C till +105°C
from +5°C till +60°C
from -30°C till +60°C
PRESSURE
max. 400 Bar
max. 400 Bar
max. 400 Bar
SPEED
max. 5.0 m/s
max. 5.0 m/s
max. 5.0 m/s
Note: The above data are maximum values and cannot be used at the same time.
SURFACE ROUGHNESS
Ra
Rmax
Sliding Surface
max. 0.2 µm
2.0 µm
Groove Base
max. 1.6 µm
6.3 µm
Groove Flanks
max. 3.2 µm
15 µm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
PERMISSIBLE SEALING GAP
B (mm)
Smax (mm)
x
150 Bar
250 Bar
400 Bar
2.2
0.25
0.20
0.15
3.2
0.4
0.25
0.15
4.2
0.4
0.25
0.20
6.3
0.5
0.30
0.20
8.1
0.6
0.35
0.25
9.5
0.7
0.50
0.30
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.
OPERATING CONDITIONS
MEDIA
Mineral oils (DIN 51524)
HFA and HFB
HFC
TEMPERATURE
from -30°C till +105°C
from +5°C till +60°C
from -30°C till +60°C
PRESSURE
max. 400 Bar
max. 400 Bar
max. 400 Bar
SPEED
max. 5.0 m/s
max. 5.0 m/s
max. 5.0 m/s
Note: The above data are maximum values and cannot be used at the same time.
SURFACE ROUGHNESS
Ra
Rmax
Sliding Surface
max. 0.2 µm
2.0 µm
Groove Base
max. 1.6 µm
6.3 µm
Groove Flanks
max. 3.2 µm
15 µm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
PERMISSIBLE SEALING GAP
B (mm)
Smax (mm)
x
150 Bar
250 Bar
400 Bar
2.2
0.25
0.20
0.15
3.2
0.4
0.25
0.15
4.2
0.4
0.25
0.20
6.3
0.5
0.30
0.20
8.1
0.6
0.35
0.25
9.5
0.7
0.50
0.30
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.
OPERATING CONDITIONS
MEDIA
Mineral oils (DIN 51524)
HFA and HFB
HFC
TEMPERATURE
from -30°C till +105°C
from +5°C till +60°C
from -30°C till +60°C
PRESSURE
max. 400 Bar
max. 400 Bar
max. 400 Bar
SPEED
max. 5.0 m/s
max. 5.0 m/s
max. 5.0 m/s
Note: The above data are maximum values and cannot be used at the same time.
SURFACE ROUGHNESS
Ra
Rmax
Sliding Surface
max. 0.2 µm
2.0 µm
Groove Base
max. 1.6 µm
6.3 µm
Groove Flanks
max. 3.2 µm
15 µm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
PERMISSIBLE SEALING GAP
B (mm)
Smax (mm)
x
150 Bar
250 Bar
400 Bar
2.2
0.25
0.20
0.15
3.2
0.4
0.25
0.15
4.2
0.4
0.25
0.20
6.3
0.5
0.30
0.20
8.1
0.6
0.35
0.25
9.5
0.7
0.50
0.30
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.
OPERATING CONDITIONS
MEDIA
Mineral oils (DIN 51524)
HFA and HFB
HFC
TEMPERATURE
from -30°C till +105°C
from +5°C till +60°C
from -30°C till +60°C
PRESSURE
max. 400 Bar
max. 400 Bar
max. 400 Bar
SPEED
max. 5.0 m/s
max. 5.0 m/s
max. 5.0 m/s
Note: The above data are maximum values and cannot be used at the same time.
SURFACE ROUGHNESS
Ra
Rmax
Sliding Surface
max. 0.2 µm
2.0 µm
Groove Base
max. 1.6 µm
6.3 µm
Groove Flanks
max. 3.2 µm
15 µm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
PERMISSIBLE SEALING GAP
B (mm)
Smax (mm)
x
150 Bar
250 Bar
400 Bar
2.2
0.25
0.20
0.15
3.2
0.4
0.25
0.15
4.2
0.4
0.25
0.20
6.3
0.5
0.30
0.20
8.1
0.6
0.35
0.25
9.5
0.7
0.50
0.30
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.